Alpha Bridge SFP ASFP-10G-LR

Product Features

  • Compliant with SFF-8431 SFP+ MSA
  • Compliant with IEEE802.3ae 10G BASE-LW/LR
  • 1310nm DFB transmitter
  • PIN photodetector
  • 2-wire interface for management specifications compliantwith
    SFF 8472 digital diagnostic monitoring interface for optical
    transceivers
  • Advanced firmware allow customer system encryption
    information to be stored in transceiver
  • Cost effective SFP+ solution, enables higher port densitiesand All-metal housing for superior EMI performance
  • Low power consumption
  • greater bandwidth
  • RoHS Compliant

Applications

  • High-speed storage area networks.
  • Computer cluster cross-connect.
  • Custom high-speed data pipes.

Absolute Maximum ratings ASFP-10G-LR

Parameter Symbol Min. Max. Units Note
Storage Temperature Tc -40 85 °C  
Operating Case Temperature Tc 0 70 °C OPAK-S10-13-CB
-40 85 °C OPAK-S10-13-IB
Supply Voltage Vcc 0 3.6 V
Relative Humidity RH 5 95 %  
RX Input Average Power Pmax --- 1.5 dBm

Recommended Operating Conditions ASFP-10G-LR

Parameter Symbol Min. Max. Units Typical
Case Operating Temperature Tc 0 70 °C OPAK-S10-13-CB
-40 85 °C OPAK-S10-13-IB
Supply Voltage Vcc 3.135 3.465 V
Supply Current ICC -- 450 mA
Power Consumption   --- 1000 mW  

Diagnostics ASFP-10G-LR

Parameter Symbol Accuracy Unit Notes
Temperature Temp ± 3 oC Over operating Temp
Voltage VCC ± 0.08 V Full operating range
Bias Current Bias ± 10 mA  
TX Power TX ± 3 dB dBm  
RX Power RX ± 3 dB dBm -1dBm to -15dBm range

Transmitter Electro-optical Characteristics ASFP-10G-LR

Parameter Symbol Min. Typ. Max. Units Note
Data Rate   --- 10.3125 --- Gbps  
Output Optical Power Pout -8.2 --- 0.5 dBm 1
Launched power OMA dBm -5.2        
Launched power OMA -TDP dBm -6.2        
Center Wavelength lC 1260   1355 nm  
Relative Intensity Noise RIN --- --- -128 dB/Hz 12dB reflection
Side Mode Suppression Ratio SMSR 30     dB  
Laser Off Power POFF --- --- -30 dBm  
Extinction Ratio ER 3.5 --- --- dB  
Transmitter Dispersion Penalty TDP --- --- 3.2 dB  
Optical Return Loss Tolerance   --- --- 12 dB  
Single Ended Output Voltage Tolerance   -0.3 --- 4 V  
C common mode voltage tolerance   15 --- --- mV  
TX Input Diff Voltage VI 180   700 mV  
TX Fault VoL -0.3   0.4 V At 0.7mA
Data Dependent Input Jitter DDJ     0.1 UI  
Data Input Total Jitter TJ     0.28 UI  

Note 1: Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

Receiver Electro-optical Characteristics ASFP-10G-LR

Parameter Symbol Min. Typ. Max. Units Note
Receiver Sensitivity in average power Psens --- --- -14.4 dBm 1
Receiver Sensitivity in OMA Psens --- --- -12.6 dBm 2
Stressed Sensitivity (OMA)   --- --- -10.3 dBm 2
Operating Center Wavelength lC 1260   1355 nm  
Vertical eye closure penalty   2.2     dB 3
Stressed eye Jitter   0.3     UIp-p 2
Overload PIN --- --- 0.5 dBm 1
Receiver power damage       1.5 dBm  
Receiver Reflectance       -12 dB  
  Receive electrical 3dB upper cutoff            
frequency 12 GHz
Loss of Signal-Asserted PA -30 --- --- dBm  
Loss of Signal-Deasserted PD --- --- -15 dBm  
Loss of Signal-Hysteresis PH 0.5 --- --- dB  
Single Ended Output Voltage Tolerance   -0.3   4 V  
RX Output Diff Voltage Vo 300   850 mV  
RX Output Rise and Fall Time Tr/Tf 30     ps 20% to 80%
Total Jitter TJ     0.7 UI  
Deterministic Jitter DJ     0.42 UI  

Note 1:  Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

Note 2:  Receiver sensitivity is informative. Stressed receiver sensitivity shall be measured with conformance test signal for BER =1x 10-12 .

Note 3:  Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.

Block Diagram of Transceiver

  • This 1310 nm DFB 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 10km.
  • The SFP+ LR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
  • The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 10GBASE-LR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (Tx_Fault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor.
  • The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non- installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.

Pin Descriptions ASFP-10G-LR

PIN Logic Symbol Name/Description Notes
1   VeeT Module Transmitter Ground 1
2 LVTTL-O TX_Fault Module Transmitter Fault  
3 LVTTL-I TX_Dis Transmitter Disable; Turns off transmitter laser output  
4 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2
5 LVTTL-I SCL 2-Wire Serial Interface Clock 2
6   MOD_DEF0 Module Definition, Grounded in the module  
7 LVTTL-I RS0 Not used  
8 LVTTL-O RX_LOS Receiver Loss of Signal Indication Active High  
9 LVTTL-I RS1 Not used  
10   VeeR Module Receiver Ground 1
11   VeeR Module Receiver Ground 1
12 CML-O RD- Receiver Inverted Data Output  
13 CML-O RD+ Receiver Data Output  
14   VeeR Module Receiver Ground 1
15   VccR Module Receiver 3.3 V Supply  
16   VccT Module Receiver 3.3 V Supply  
17   VeeT Module Transmitter Ground 1
18 CML-I TD+ Transmitter Non-Inverted Data Input  
19 CML-I TD- Transmitter Inverted Data Input  
20   VeeT Module Transmitter Ground 1

Note:

  1. Module ground pins GND are isolated from the module.
  2. Shall be pulled up with 7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.

Optical Receptacle Cleaning Recommendations:

All fiber stubs inside the receptacle portions were cleaned before shipment. In the event of contamination of the optical ports, the recommended cleaning process is the use of forced nitrogen. If contamination is thought to have remained, the optical ports can be cleaned using a NTT international Cletop® stick type and HFE7100 cleaning fluid. Before the mating of patch-cord, the fiber end should be cleaned up by using Cletop® cleaning cassette.

Dimensions ASFP-10G-LR

Model Number Part Number     Reach Input/Output Signal Detect Voltage Temperature
ASFP-10G-LR OPAK-S10-13-CB 10KM AC/AC TTL 3.3V 0°C to 70 °C
ASFP-10G-LR-I OPAK-S10-13-CB 10KM AC/AC TTL 3.3V -40°C to 85 °C
DOWNLOAD BROCHURE
Scroll to Top