Alpha Bridge AXFP-10G-ZR+

Features

  • 4 CWDM lanes MUX/DEMUX design.
  • Up to 2Gb/s data rate per wavelength.
  • QSFP+ MSA compliant.
  • IEEE 3ba Electrical Interface.
  • Digital diagnostic capabilities.
  • Compliant with QDR/DDR Infiniband data rates.
  • Up to 150m transmission on OM3 multimode fiber (MMF) or 2km transmission on single mode fiber (SMF).
  • Operating case temperature: 0 to 70℃.
  • Maximum power consumption 5W.
  • LC duplex connector.

Applications

  • 40GBASE-LX4 Ethernet Links.
  • Infiniband QDR and DDR interconnects.
  • Client-side 40G datacom connections.

Absolute Maximum Ratings AXFP-10G-ZR+

Parameter Symbol Min Max Unit
Storage Temperature Ts -40 85 °C
Operating Case Temperature TOP 0 70 °C
Power Supply Voltage Vcc -0.5 3.6 V
Relative Humidity (non-condensation) RH 0 85 %
Damage Threshold, each Lane THd 4.5   dBm

Recommended Operating Conditions AXFP-10G-ZR+

Parameter Symbol Min Typical Max Unit
Operating Case Temperature TOP 0   +70 °C
Power Supply Voltage Vcc 3.135 3.3 3.465 V
Data Rate, each Lane     10.3125 11.2 Gb/s
Control Input Voltage High   2   Vcc V
Control Input Voltage Low   0   0.8 V
Link Distance with (OM3 MMF) D_MMF     150 m
Link Distance (SMF) D_SMF     2 km

Electrical Characteristics AXFP-10G-ZR+

Parameter Symbol Min Typical Max Unit Notes
Power Consumption       3.5 W  
Supply Current Icc     1.1 A  
Transceiver Power-on Initialization Time       2000 ms 1

Notes: Power-on initialization time is the time from when the power supply voltages reach and remain above the minimum recommended operating supply voltages to the time when the module is fully functional.

Optical Characteristics AXFP-10G-ZR+

Parameter           Symbol Min Typical Max Unit Notes
Wavelength assignment L0 1264.5 1271 1277.5 nm  
L1 1284.5 1291 1297.5 nm  
L2 1304.5 1311 1317.5 nm  
L3 1324.5 1331 1337.5 nm  

Transmitter Electro-optical Characteristics AXFP-10G-ZR+

Parameter Symbol Min. Typ.                Max. Units Note
Operating Date Rate   9.95 11.3 Gbps  
Input Reference Clock Rate     Not Required    
Output Optical Power Pout 1 ---             4 dBm  
Extinction Ratio ER 9   dB  
Center Wavelength °C 1530 1565 nm  
Sidemode Supression ratio SSRmin 30     dB
Relative Intensity Noise RIN --- ---          -130 dB/Hz  
Output Eye Compliant with IEEE802.3ae
Differential Input Voltage VDIFF 0.12 --- 1.0
Transmit Fault Output-Low TX_FAULTL 0.0 --- 0.5
Transmit Fault Output-High TX_FAULTH 2.4 --- Vcc
TX_DISABLE Assert Time t_off --- --- 10
TX_DISABLE Negate Time t_on --- --- 2
Time to initialize t_init --- --- 300
Interrupt assert delay Interrupt _on --- --- 200
Interrupt negate delay Interrupt_off --- --- 500
P_Down/RST assert delay P_Down/RST_on     100
Mod_NR assert delay Mod_nr_on     1
Mod_NR negate delay Mod_nr_off     1
P-Down reset time   10    
RX_LOS assert delay t_loss_on     100

Note: Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

Receiver Electro-optical Characteristics AXFP-10G-ZR+

Parameter Symbol Min. Typ. Max. Units Note
Optical Input Power-maximum PIN -7 --- --- dBm BER < 10-12
Receiver Sensitivity PIN --- --- -24 dBm BER < 10-12
Receiver Sensitivity (OMA) PIN --- --- -22.1 dBm BER < 10-12
Operating Center Wavelength C 1270 --- 1600 nm  
Receiver Reflectance Rrx 27 --- --- dB  
Dispersion Panelty       3 dB Up to 80 km
Loss of Signal-Asserted PA --- --- -30 dBm  
Loss of Signal-Deasserted PD -22 --- --- dBm  
Differential Output Voltage VDIFF 0.6   0.8 V  
TTL Input High Voltage   2   Vcc V  
TTL Input Low Voltage   0   0.8 V  
TTL output High Voltage   2.4 --- Vcc V  
TTL output Low Voltage   0 --- 0.4 V  
Receiver Loss of Signal Assert Time                                                                           tA,RX_LOS                                                                                                              --- --- 100 μs  
Recover Loss of Signal Assert Time                                                                           tD,RX_LOS                                                                                                              --- --- 100 μs  

Block Diagram of Transceiver

MOD_NR

The Mod_NR is an output pin that when High, indicates that the module has detected a condition that renders transmitter and or receiver data invalid, shall consist of logical OR of the following signals:

  • Transmit Signal Conditioner Loss of Lock
  • Transmitter Laser Fault
  • Receiver Signal Conditioner Loss of Lock
 
MOD_DESEL

The Mod_DeSel is an input pin. When held Low by the host, the module responds to 2-wire serial communication commands. The Mod_DeSel allows the use of multiple XFP modules on a single 2-wire interface bus. When the Mod_DesSel pin is “High”, the module shall not respond to or acknowledge any 2-wire interface communication from the host.

INTERRUPT

Interrupt is an output pin. When “Low”, indicates possible module operational fault or a status critical to the host system.

TX_DIS

TX_DIS is an input pin. When TX_DIS is asserted High, the XFP module transmitter output must be turned off.

MOD_ABS

Mod_ABS is pulled up to Host_Vcc on the host board and grounded in the XFP module. Mod_ABS is then asserted “High” when the XFP module is physically absent from a host slot.

RX_LOS

The RX_LOS when High indicates insufficient optical power for reliable signal reception.

P_DOWN/RST

This is a multifunction pin for module Power Down and Reset. The P_Down/RST pin must be pulled up to VCC3 in the XFP module.

POWER DOWN FUNCTION

The P_Down pin, when held high by the host, places the module in the standby (Low Power) mode with a maximum power dissipation of 1.5W. This protects hosts which are not capable of cooling higher power modules which may be accidentally inserted.

Optical Receptacle Cleaning Recommendations


All fiber stubs inside the receptacle portions were cleaned before shipment. In the event of contamination of the optical ports, the recommended cleaning process is the use of forced nitrogen. If contamination is thought to have remained, the optical ports can be cleaned using a NTT international Cletop® stick type and HFE7100 cleaning fluid.  Before the mating of patch-cord, the fiber end should be cleaned up by using Cletop® cleaning cassette.

Ordering Information AXFP-10G-ZR+

Model Number Part Number Reach Input/Output Signal Detect Voltage Temprature
XFP-ZR+ OP7K-SA0-15-C 25dB AC/AC TTL 3.3V -5°C to 70°C
Download Brochure
Scroll to Top