Alpha Bridge AXFP-10G-ZR

Features

  • Compliant with XFP MSA INF-8077i.
  • Compliant with 3ae 10GBASE-ZW/ZR Ethernet.
  • Compliant with SONET OC-192/SDH STM-64 ITU-TG.959.1 P1L1-2D2.
  • Compliant with SONET OC-192/SDH STM-64 with ITU-T 709.
  • Compliant with 80km 10G Ethernet with ITU-T 709 FEC.
  • Compliant with 80km 10G Fiber Channel.
  • Differential LVPECL inputs and CML outputs.
  • TTL signal detect.
  • Hot Pluggable.
  • Power consumption<3.5W.
  • Class 1 laser product complies with EN 60825-1.
  • RoHS Compliant.

Absolute Maximum Ratings AXFP-10G-ZR

Parameter Symbol Min. Max. Units Note
Storage Temperature TS -40 85 °C  
Supply Voltage Vcc3 -0.5 4.0 V  
Input Voltage VIN -0.5 6.0 V  

Recommended Operating Conditions AXFP-10G-ZR

Parameter Symbol Min. Max. Units Note
Case Operating Temperature TC -5 70 °C  
Supply Voltage Vcc3 3.1 3.5 V  
Supply Current Icc3 --- 500 mA  
Supply Voltage Vcc5 4.5 5.5 V  
Supply Current Icc5 --- 350 mA  

Diagnostics AXFP-10G-ZR

Data Address Parameter Range Accuracy
96-97 Temperature -40 °C to 85 °C ±3°C
100-101 Bias Current 0 to 120mA ±10%
102-103 TX Power -1 to +5dBm ±2dB
104-105 RX Power -24 to -6dBm ±2dB
106-107 Vcc3 Voltage 2.9~3.7 Volts ±3%
108-109 Vcc5 Voltage 4.5~5.5 Volts ±3%

Transmitter Electro-optical Characteristics AXFP-10G-ZR

Parameter Symbol Min. Typ. Max. Units Note
Operating Date Rate   9.95   11.3 Gbps  
Input Reference Clock Rate     Not Required    
Output Optical Power Pout 0 --- 4 dBm  
Extinction Ratio ER 9     dB  
Center Wavelength C 1530   1565 nm  
Sidemode Supression ratio SSRmin 30       dB
Relative Intensity Noise RIN --- --- -130 dB/Hz  
Output Eye Compliant with IEEE802.3ae
Differential Input Voltage VDIFF 0.12 --- 1.0 V
Transmit Fault Output-Low TX_FAULTL 0.0 --- 0.5 V
Transmit Fault Output-High TX_FAULTH 2.4 --- Vcc V
TX_DISABLE Assert Time t_off --- --- 10 μs
TX_DISABLE Negate Time t_on --- --- 2 ms
Time to initialize t_init --- --- 300
Interrupt/assert delay Interrupt _on --- --- 200 ms
  Interrupt_off --- ---           500
P_Down/RST assert delay P_Down/RST_on   100 ms
Mod_NR assert delay Mod_nr_on   1 ms
Mod_NR negate delay Mod_nr_off   1 ms
P-Down reset time   10   ms
RX_LOS assert delay t_loss_on   100 μs
RX_LOS negate delay t_loss_off   100 μs

 Note: Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

Receiver Electro-optical Characteristics AXFP-10G-ZR

Parameter Symbol Min. Typ. Max. Units Note
Optical Input Power-maximum PIN -7 --- --- dBm BER < 1012
Receiver Sensitivity PIN --- --- -23 dBm BER < 1012
Receiver Sensitivity (OMA) PIN --- --- -22.1 dBm BER < 1012
Operating Center Wavelength °C 1270 --- 1600 nm  
Receiver Reflectance Rrx 27 --- --- dB  
Dispersion Panelty       3 dB 80 km
Loss of Signal-Asserted PA --- --- -30 dBm  
Loss of Signal-Deasserted PD -22 --- --- dBm  
Differential Output Voltage VDIFF 0.6   0.8 V  
TTL Input High Voltage   2   Vcc V  
TTL Input Low Voltage   0   0.8 V  
TTL output High Voltage   2.4 --- Vcc V  
TTL output Low Voltage   0 --- 0.4 V  
Receiver Loss of Signal Assert Time (off to on) tA,RX_LOS --- --- 100 μs  
Recover Loss of Signal Assert Time (on to off) tD,RX_LOS --- --- 100 μs  

Block Diagram of Transceiver

MOD_NR

The Mod_NR is an output pin that when High, indicates that the module has detected a condition that renders transmitter and or receiver data invalid, shall consist of logical OR of the following signals:

  • Transmit Signal Conditioner Loss of Lock
  • Transmitter Laser Fault
  • Receiver Signal Conditioner Loss of Lock
 
MOD_DESEL

The Mod_DeSel is an input pin. When held Low by the host, the module responds to 2-wire serial communication commands. The Mod_DeSel allows the use of multiple XFP modules on a single 2-wire interface bus. When the Mod_DesSel pin is “High”, the module shall not respond to or acknowledge any 2-wire interface communication from the host.

INTERRUPT

Interrupt is an output pin. When “Low”, indicates possible module operational fault or a status critical to the host system.

TX_DIS

TX_DIS is an input pin. When TX_DIS is asserted High, the XFP module transmitter output must be turned off.

MOD_ABS

Mod_ABS is pulled up to Host_Vcc on the host board and grounded in the XFP module. Mod_ABS is then asserted “High” when the XFP module is physically absent from a host slot.

RX_LOS

The RX_LOS when High indicates insufficient optical power for reliable signal reception.

P_DOWN/RST

This is a multifunction pin for module Power Down and Reset. The P_Down/RST pin must be pulled up to VCC3 in the XFP module.

POWER DOWN FUNCTION

The P_Down pin, when held high by the host, places the module in the standby (Low Power) mode with a maximum power dissipation of 1.5W. This protects hosts which are not capable of cooling higher power modules which may be accidentally inserted.

Pin Description AXFP-10G-ZR

Pin Logic Symbol Name/Description Note
1   GND Module Ground 1
2   VEE5 Optional -5.2V Power Supply  
3 LVTTL-I Mod_DeSel Module De-select; When held low allows module to respond to 2-wire serial interface  
4 LVTTL-O   Interrupt Interrupt; Indicates presence of an important condition which can be read over the 2-wire serial interface 2
5 LVTTL-I TX_DIS Transmitter Disable; Turns off transmitter laser output  
6   VCC5 +5V Power Supply  
7   GND Module Ground 1
8   VCC3 +3.3V Power Supply  
9   VCC3 +3.3V Power Supply  
10 LVTTL-I/O SCL 2-Wire Serial Interface Clock 2
11 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2
12 LVTTL-O Mod_Abs Indicates Module is not present. Grounded in the Module 2
13 LVTTL-O Mod_NR Module Not Ready; Indicating Module Operational Fault 2
14 LVTTL-O RX_LOS Receiver Loss of Signal Indicator 2
15   GND Module Ground 1
16   GND Module Ground 1
17 CML-O RD- Receiver Inverted Data Output  
18 CML-O RD+ Receiver Non-Inverted Data Output  
19   GND Module Ground 1
20   VCC2 +1.8V Power Supply 3
    21     LVTTL-I P_Down/RST Power down; When high, requires the module to limit power consumption to 1.5W or below, 2-Wire serial interface must be functional in the low power mode.
Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle.
22   VCC2 +1.8V Power Supply 3
23   GND Module Ground 1
24 PECL-I RefCLK+ Not Required  
25 PECL-I RefCLK-  
26   GND Module Ground 1
27   GND Module Ground 1
28 CML-I TD- Transmitter Inverted Data Input  
29 CML-I TD+ Transmitter Non-Inverted Data Input  
30   GND Module Ground 1

Optical Receptacle Cleaning Recommendations


All fiber stubs inside the receptacle portions were cleaned before shipment. In the event of contamination of the optical ports, the recommended cleaning process is the use of forced nitrogen. If contamination is thought to have remained, the optical ports can be cleaned using a NTT international Cletop® stick type and HFE7100 cleaning fluid.  Before the mating of patch-cord, the fiber end should be cleaned up by using Cletop® cleaning cassette.

Ordering Information AXFP-10G-ZR

Model Number Part Number Reach Input/Output Signal Detect Voltage Temprature
AXFP-10G-ZR OP7K-S80-15-C 80 km AC/AC TTL 3.3V/5V -5°C to 70°C
DOWNLOAD BROCHURE
Scroll to Top